ZyXEL omni.net LCD+M Uživatelský manuál Strana 162
- Strana / 186
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Technical Reference for ZyXEL omni.net series
B-10
All the Following Commands Require a 'AT' Prefix
S Com. bit dec hex Function and description +Def./Ref.
S41= bit dec hex Bit mapped register +000
3 8 8 Enable CCITT signals 140 and 141 on EIA-232D interface.
5 32 20 DSR follows DCD and pulses (see S44b4).
&Sn
6 64 40 Force S0>=2. S0
S42= bit dec hex Bit mapped register +000
3 8 8 Disable escape sequence code in answer mode.
6 64 40 Disable <RINGING> result code.
Xn
7 128 80 DCD forced on, but pulse off for 0.5 seconds at carrier loss. &C0
S44= bit dec hex Bit mapped register +000
3 8 8
'ATDSn' initiates auto-dial of the stored numbers
consecutively until connection is made.
&Zn
S38b0
4 16 10 DSR follows DTR (see also S41b5).
&Sn
S50= 0-25
5
Inactivity timer for RS 232 port.
This timer counts when there is no data flow in or out of the
RS 232 serial port; omni.net will hang up , when timed out.
Units is 10 seconds.
'000' disables timer.
+000
S56= 0-25
5
0-FF Hook flash detected time for POTS port adapter, in units of
10ms.
Default setting 50 = 0.5 seconds.
+050
S57= fax
Class
S61= bit dec hex
3 0 (*) 0 MP data sent in rotate mode.
1 1 MP data sent in split mode.
S64= dec hex +005
0-25
5
0-FF Security callback timer in unit of 1 second.
S78= bit dec hex Bit mapped register
0 0 (*) 0 Can get busy tone from Phone 1.
- ISDN Terminal Adapters 2
- Limited Warranty 3
- Become a Registered Owner 3
- Contents 5
- PART II ISDN FUNCTION 6
- PART III VOICE FEATURES 7
- PART IV DATA FUNCTION 8
- PART V FAX/MODEM FUNCTION 9
- PART VII APPENDICES 10
- Content of Tables 13
- Content of Figures 17
- Preface 18
- How to Use This Manual 19
- Other References 19
- Part I 21
- Introduction 21
- Chapter 1 23
- Intelligent Features 24
- Specifications 24
- Key Features Summary 25
- Chapter 2 27
- ISDN Configuration Manager 27
- Bumping 31
- Configuring ISDN Parameters 32
- Chapter 3 33
- LCD/LCD+M) 33
- LCD Panel Functions 34
- Right key: 35
- Left key: 35
- Up key: 35
- Down key: 35
- Idle Screen 36
- Set Clock sub-menu 36
- Set Display Mode sub-menu 36
- Dial In Log 37
- Stored Phone List 37
- Dial Out Log 38
- Active Status 39
- Clock Options 40
- Update Clock 41
- Set Display Mode 42
- Dial In Log Options 43
- button 44
- Dial Out Log Options 45
- Part II 47
- ISDN Function 47
- Chapter 4 49
- ISDN Communication Basics 49
- Supported AT Command Types 51
- LCD/LCD+M/Plus) 54
- Placing a Data Call 55
- Incoming Calls 55
- Command Description 58
- ATS119.3=0 58
- ATS119.3=1 58
- Best effort call answering 58
- Part III 61
- Voice Features 61
- Supplementary Service 63
- Chapter 5 63
- Call Waiting 64
- Call Hold/Retrieve 64
- Three Way Conferencing 66
- Starting a conference call 66
- Call Forwarding 68
- For DSS1 switch 68
- Chapter 6 71
- Feature Phone Operation 71
- Flash Key Commands 72
- InterCom 72
- Receiving a Second Call 73
- Call Broker 74
- Call Reject 75
- Call Transfer 75
- Three-Way Conference Call 76
- Last Number Redial 77
- Quick Dial 77
- Part IV 79
- Data Function 79
- Chapter 7 81
- Feature List 82
- Async to Sync Conversion 82
- Authentication Conversion 82
- Multilink PPP 84
- Call Bumping 84
- Bandwidth On Demand (BOD) 86
- BACP/BAP 86
- Chapter 8 89
- ISDN Communications 89
- V.110 Outgoing Protocol 91
- V.120 Outgoing Protocol 92
- X.75 Outgoing Protocol 93
- Speeds of 128Kbps 95
- V.120 Bundled Call 95
- X.75 Bundled Call 97
- Table 52. V.42bis AT Command 98
- Data Compression with X.75 100
- Security Settings 101
- Modifying the User Passwords 105
- Password: 106
- Part V 107
- Fax/Modem Function 107
- Chapter 9 109
- Internal Fax/Modem Function 109
- MNP Protocols 110
- Xmodem, Ymodem, and Zmodem 110
- Fax and Facsimile 111
- Modem as a fax 111
- EIA Class 1 Fax Commands 111
- Answering a Call Using MSN 113
- Control Data Compression 115
- Fax Operation 115
- Fax Command Sets 116
- Appendix D) 118
- Part VI 119
- Diagnostics 119
- Firmware Update 119
- Chapter 10 121
- Power-on Self-test 122
- Resetting Your omni.net 124
- Capturing the Protocol Data 125
- Analyzing the Captured Data 126
- Chapter 11 129
- Firmware Upgrade 129
- Kernel Mode 130
- Part VII 133
- Appendices 133
- Appendix A 135
- AT Command Set Reference 135
- AT Commands Description 136
- AT Commands Prefix (AT) 136
- Description of ATI3 Output 144
- Fax Command 151
- Appendix B 153
- Setting S-registers 154
- S-Register Descriptions 156
- Appendix C 181
- Appendix D 183
- Serial Port Interface 183
Související produkty a manuály pro Modemy ZyXEL omni.net LCD+M
Modemy ZyXEL 3356P Uživatelský manuál
(30 stránky)
(30 stránky)
Modemy ZyXEL P841C Uživatelský manuál
(41 stránky)
(41 stránky)
Modemy ZyXEL P-660M Uživatelský manuál
(2 stránky)
(2 stránky)
Modemy ZyXEL ADSL-Modem Uživatelský manuál
(20 stránky)
(20 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce